- whatsapp +51955515985
- support@ecuforcetruck.com
- 24/7 Customer Support
Menu
Shop
Account
Subtotal: $0.00
No products in the cart.
Lamp:
None
Reason:
An offset in the particulate matter sensor reading has been detected.
Effect:
Possible reduced engine performance.
The aftertreatment particulate matter sensor is a smart device and communicates with the Engine Control Module (ECM) via the J1939 data link.
Circuit Description:
The aftertreatment particulate matter sensor is a smart device and communicates with the Engine Control Module (ECM) via the J1939 data link. The aftertreatment particulate matter sensor performs internal diagnostics and reports malfunctions back to the primary ECM using the J1939 data link. The particulate matter sensor is permanently attached to the particulate matter control module. They are serviced as a single component and can not be replaced individually. The aftertreatment particulate matter sensor is used to measure the soot emissions at the outlet of the aftertreatment system.
Component Location:
The aftertreatment particulate matter sensor location can vary depending on engine application. It is usually located in the exhaust system at the outlet of the Selective Catalytic Reduction (SCR) catalyst.
Conditions for Running the Diagnostics:
This diagnostic runs continuously when the engine is running.
Conditions for Setting the Fault Codes:
The aftertreatement particulate matter sensor has detected the probe temperature value is not changing with conditions.
Action Taken When the Fault Code is Active:
The ECM illuminates the amber check engine lamp and/or Malfunction Indicator Lamp (MIL) after the diagnostic fails on two consecutive trips.
Conditions for Clearing the Fault Code:
1. Perform a key cycle.
2. Start and idle the engine.
3. To validate the repair, use the diagnostic tool to perform the “aftertreatment current based particulate matter sensor regeneration test” found in ECM diagnostic test.
4. The ECM will turn off the amber check engine lamp immediately after the diagnostic runs and passes.
5. The fault code status displayed by the diagnostic tool will change to inactive immediately after the diagnostic runs and passes.
6. For On-Board Diagnostics (OBD) engines, the ECM will extinguish the Malfunction Indicator Lamp (MIL) after three consecutive trips where the diagnostic runs and passes.
7. The reset all faults command in the diagnostic tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk:
Possible causes for this fault include:
Malfunctioning aftertreatment particulate matter sensor.
Related
Categories Cumminz, DTC TRUCKS, Tags , 1, 2/21, 2018, 6794, 7854, Aftertreatment, CM2450, Code, Cummins, Data, Drifted, Fault, FMI, Low, Module, Newer, Not, Particulate, PID, Rational, Sensor, SPN, X124B, X15
Wiring Diagrams
Component Locators
- JOHN DEERE SERVICE ADVISOR 5.3.225 DATABASE AG + CF ENGLISH 2023
John Deere$250.00
Rated 0 out of 5
- Navistar international OnCommand service information 2018 software trucks
Navistar$50.00
Rated 0 out of 5
- Volvo Premium Tech Tool PTT 2.8.130 Diagnostic Software 04.2022 ACPI ( 1 PC )
Trucks software$143.00
Rated 0 out of 5
- DOWNLOAD Paccar ESA Electronic Service Analyst 5.5.0 Diagnostic Software 2023
PACCAR$96.00
Rated 0 out of 5
- Wabco PIN Code Calculator Diagnostic Software PIN 1 PIN 2
Trucks software$10.00
Rated 0 out of 5
- Diagnostic Software PSI Powerlink 2.3.1
PSI Powerlink$94.00
Rated 0 out of 5
- Diamond Logic Builder DLB 2018
Navistar$40.00
Rated 0 out of 5
- Detroit BackDoor Password Generator V1 V2
Detroit$30.00
Rated 0 out of 5
- VOLVO PROSIS 2023 ( 11.2022 )
Trucks software$96.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROTRON 108-118-128
Trucks software$38.00
Rated 0 out of 5
- Volvo PROSIS Offline 2019 Parts Catalog Installation Service
Trucks software$45.00
Rated 0 out of 5
Scania$30.00
Rated 0 out of 5
- International Truck ISIS – Oncommand Service Information Q4.2020 [04.2020]
Navistar$85.00
Rated 0 out of 5
- CAT CDVR PC Software – Caterpillar Digital Voltage Regulator (CDVR) WINDOWS 10
CAT$45.00
Rated 0 out of 5
- Cumming Caltem 5.9.1 2022 ( 1 PC )
cummisznn$78.00
Rated 0 out of 5
- CAT SIS caterpillar 2021 Full Service Dealer
CAT$90.00
Rated 0 out of 5
- Download Renault Trucks NG3 NG10 calculator v0.1
Renault$26.00
Rated 0 out of 5
- Meritor WABCO Toolbox 12.12 Software
Trucks software$40.00
Rated 0 out of 5
- Allison Doc Premium Update 2023 v2
Allison$102.00
Rated 0 out of 5
- Bendix 6.16 ACom Diagnostics ( bendix software trucks )
Bendix$35.00
Rated 0 out of 5
Related products
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- SERVICE MANUAL HINO FD.FE.FF.SG 2006
HINO$34.00
Rated 0 out of 5
- MANUAL SERVICE DEUTZ AGROTRON 106-110-115-120-135-150-165 MK3
DEUTZ$34.00
Rated 0 out of 5
- MANUAL SERVICE Deutz Combine 5650 H, 5660 HTS5670 H / HTS5680 H, 5690 HTS
DEUTZ$38.00
Rated 0 out of 5
- SERVICE MANUAL Carrie TEMPRA 440S SERIES
CARRIE$20.00
Rated 0 out of 5
- SERVICE MANUAL Carrie Integra 30s
CARRIE$20.00
Rated 0 out of 5
DETROIT$38.00
Rated 0 out of 5
FUSO$30.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 231 SMS
BOBCAT$60.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 440b sms
BOBCAT$45.00
Rated 0 out of 5
- SERVICE MANUAL MACK E-TECH
MACK$28.00
Rated 0 out of 5